Nozzle broken???

HiraMahi

Gravity Guru
Hi folks, my evolution silver line spry bad, and the small line are not continued and spray like point and make like over spray with low pressure, so... i soiled with paint the part coming out of the needle. Then I extract the needle and measured the part that comes out, which is about two millimeters.

287a1f6da899bac42db777b8d4ba2016.jpg


9688e0e6adf464ab9022477f640dfa0f.jpg


72b4235665618ad1d1ace678b0d019d7.jpg




Inviato dal mio SM-G930F utilizzando Tapatalk
 
Sorry I show you the 0,2mm head.
This is the right one 0,4mm.
You see there is no difference to your head.
0cbda032927bf58241632bc8b30263fa.jpg


Gesendet von meinem SM-G388F mit Tapatalk
 
Sorry I show you the 0,2mm head.
This is the right one 0,4mm.
You see there is no difference to your head.
0cbda032927bf58241632bc8b30263fa.jpg


Gesendet von meinem SM-G388F mit Tapatalk
I have the same problem of spry bad with every two kit.
I dont know what i can do to solved. :(

Inviato dal mio SM-G930F utilizzando Tapatalk
 
I have the Evolution Two in One.
5ec8bd6f4ab9052e3aa689d7bec7137c.jpg


Gesendet von meinem SM-G388F mit Tapatalk
I have the silverline edition, is almost the same.
My airbrush give mr lot of problem from when i buy.
I dont know why they spray so bad...
Specialy for the small line...
e12999335b45f1630029e9bdee901ab6.jpg


Inviato dal mio SM-G930F utilizzando Tapatalk
 
Micha thank you for the answer, today i try contact again the delear, i need solved the problem.

Inviato dal mio SM-G930F utilizzando Tapatalk
 
The most of the problems are coming from the colors. (in my case)
I work mostly with Schmincke Aerocolors. The opake colors needs a lot of thinning however the transparents I can spray straight from the bottle.
test your colors with different mixing ratios. The thinner the color the less pressure.
 
The most of the problems are coming from the colors. (in my case)
I work mostly with Schmincke Aerocolors. The opake colors needs a lot of thinning however the transparents I can spray straight from the bottle.
test your colors with different mixing ratios. The thinner the color the less pressure.

Thank you for the information.
How you work with schmincke colors? They are good?

At the moment i used too much the createx (classic, transparent, pearl) hansa pro color and ferrario.
I try to mix with different ratio and different pressure, but i have every time the same problem. :(

Inviato dal mio SM-G930F utilizzando Tapatalk
 
I contact the delear, i will send the airbrush tomorrow, i hope to solved the problem.

Inviato dal mio SM-G930F utilizzando Tapatalk
 
So are you talking about the paint on the end of the needle...? Looks like tip dry... as you spray paint drys on the needle...
 
So are you talking about the paint on the end of the needle...? Looks like tip dry... as you spray paint drys on the needle...
Nop, i talk about the airbrush spry bad like this pic, the color are not continued and spry irregular.

e385c0de4eac31e74063b49008587f17.jpg


Inviato dal mio SM-G930F utilizzando Tapatalk
 
This is a pic of the airbrush clean.
I give the body, nozxle ecc under cleaner for a few hours.

Whaht do you tink?
Is ok how they spry now?

421e0cc90077670ef7895bab1503740b.jpg


Inviato dal mio SM-G930F utilizzando Tapatalk
 
Back
Top